Custom Cabinets in Albuquerque, NM

Why Albuquerque kitchens need custom

Albuquerque has a hundred years of housing stock and almost none of it is square. Adobe and territorial houses in the valleys with walls that lean. Mid-century ranches in Nob Hill, Ridgecrest, and the near Heights with eight-foot ceilings and a soffit over short uppers. Seventies split-levels with a galley kitchen and a peninsula. Nineties and 2000s production houses on the Westside and in the far Heights with a layout that is fine and finishes that are not. Each one of those is a different problem, and a cabinet that comes in three-inch increments solves none of them well.

We build to the room. Every wall is measured at three heights, the boxes are built in our Edgewood shop to those dimensions in three-quarter-inch plywood, the doors are sprayed with a catalyzed finish, and the finished ends and fillers are scribed to the real wall on install day. Then the countertop is templated against those cabinets and cut in the same building. One shop, one crew, one number.

What Albuquerque homeowners are asking for

Painted Shaker in white or greige with a deep blue or green island is the most common request, from Nob Hill to Ventana Ranch. Flat-slab rift white oak or walnut for a modern Foothills kitchen. Stained knotty alder with a simple flat panel for a North Valley or South Valley adobe. Soffits removed and uppers run to the ceiling in Heights houses. A pantry wall where a peninsula used to close off the kitchen. Deep drawers instead of lower doors almost everywhere, because that is how people actually reach a pot.

Custom versus refacing versus stock

We also reface cabinets in Albuquerque, so we have no reason to push new boxes when the old ones are sound. Custom wins when you want to move the sink, add an island, open a wall, or when the existing boxes are particleboard that has met water. Refacing wins when the boxes are plywood and square and only the doors are dated. Stock wins almost never in an Albuquerque house, because the wasted inches and filler strips cost more in storage than they save in money. We quote the right one and tell you which we would pick.

Neighborhoods we build for

The Northeast Heights, North Valley, Los Ranchos, Westside, South Valley, Nob Hill, UNM, Ridgecrest, Four Hills, the Foothills, and High Desert. Full details on our Albuquerque service page.

How we build cabinets for Albuquerque homes

Custom does not mean expensive for its own sake. It means the box is built to the wall you actually have, in the increment you actually need, rather than the closest three-inch stock size plus a filler strip. In a region where very few walls are square and ceiling heights change room to room, that is usually the difference between a kitchen that looks fitted and one that looks installed.

• Boxes. Three-quarter-inch plywood, not particleboard. Particleboard that has met water once — a slow dishwasher leak, a sink trap drip — swells and never recovers. Plywood survives it.
• Doors and drawer fronts. Shaker, flat-slab, raised panel, or inset. Paint-grade maple or poplar, stain-grade alder, hickory, oak, or walnut. Knotty alder is the regional favorite for a reason: it takes a warm stain and hides the dings of a real household.
• Hardware. Soft-close hinges and full-extension undermount drawer slides as standard. Not an upgrade.
• Finish. Sprayed in the shop, not brushed on site. Conversion varnish over stain, or a catalyzed enamel over paint. It is the difference between a finish that holds up to fifteen years of hands and one that chips at the pulls in two.
• Layout. Drawers where you reach down, doors where you reach up. Pull-outs for trash and spices. A pantry that uses the full height of the wall. This is the part that makes a kitchen work, and it is the part a catalog cannot do.

Typical installed pricing runs $350–$900 per linear ft installed depending on wood species, door style, and how much of the run is drawers. Full details on custom cabinets →

Why hiring one shop for cabinets and countertops matters in Albuquerque

Most remodels in Albuquerque involve two companies who have never met: one sets cabinets, another fabricates stone. When the countertop does not sit flat, each explains why it is the other’s fault, and you are left holding a gap, a tube of caulk, and two phone numbers.

We run both sides under one roof. Cabinets are set and leveled by our crew, then the countertop is templated against those cabinets, cut in the same building, and installed by the same people. If something is off, it is ours, and there is nobody to point at. That is not a slogan. It is the reason the business is structured this way, and it is the reason the seams line up.

It also has a practical scheduling benefit. One contractor means one calendar, so cabinets and tops land in sequence instead of leaving your kitchen torn out for a week while a second company finds an opening.

How a project runs with us

1. Call or send the form. Jesus answers, asks what you are trying to do, and books a time to come measure. Albuquerque is about thirty-five minutes down I-40 from the shop and we are in the city nearly every working day.
2. On-site measurement and a straight conversation. We look at the room, the plumbing, the walls, and how you cook. If a material is wrong for your situation, this is where we say so.
3. One written number. Template, fabrication, tear-out, install, haul-away, sealing. No per-item surprises after the fact.
4. Slab or sample approval. For natural stone you see the actual slab and where the cuts land. For cabinets you approve a door sample and a finish chip.
5. Fabrication in Edgewood. Cabinets built and finished in the shop. Countertops laser-templated once the cabinets are set and level, then cut on the CNC and polished.
6. Install by the same crew. The people who measured are the people who build and the people who install. One point of contact from first visit to final walkthrough.

Countertop-only projects typically run one to two weeks from template to install. Full cabinet packages run four to eight weeks depending on wood and finish. A complete kitchen remodel is usually six to ten weeks once materials are approved.

Typical custom cabinets pricing in Albuquerque

Service	Typical range	Unit
Custom cabinets	$350 – $900	linear ft installed
Cabinet refacing	$150 – $350	linear ft installed

Ranges include template, fabrication, standard edge, tear-out of existing tops, install, and sealing where applicable. Exotic slabs, waterfall edges, full-height backsplashes, and structural changes move a project toward the top of the range. Every job is quoted individually after an on-site measurement. See the full pricing guide →

Other services in Albuquerque

• Granite Countertops in Albuquerque
• Quartz Countertops in Albuquerque
• Cabinet Refacing in Albuquerque
• Kitchen Remodeling in Albuquerque
• Bathroom Remodeling in Albuquerque
• All services in Albuquerque

Custom Cabinets in nearby cities

• Custom Cabinets in Rio Rancho
• Custom Cabinets in Santa Fe
• Custom Cabinets in Edgewood
• Custom Cabinets overview

Also serving the areas around Albuquerque

Our shop in Edgewood puts the whole metro, the East Mountains, and the Santa Fe corridor within a normal working radius. There is no travel charge anywhere on this list.

• Northeast Heights
• North Valley
• Westside Albuquerque
• Los Ranchos de Albuquerque
• Rio Rancho
• Corrales
• Bernalillo
• Placitas